"FIRST ONE LID, THEN ANOTHER" JEWELRY BOX!!!

Hello, everyone!!!

I'm so glad to also be presenting this little box as my DT project over at Sheila's today.  Why not click on her name for a direct link to her blog and leave me a comment there too -- I love your comments!!!  And while you're there take a look around!!!  Sheila has all kinds of fascinating and things going on!

This is the little jewelry box I'll be sharing today:

 

What interested me about this little jewelry box is that it has 2 lids, one on each side of the box, and you open both lids to get to the inside box!  You'll see further down in the post!

But what's a jewelry box without a piece of jewelry?  So, just to give you an idea of how cute this is as a jewelry box, I made a pendant to match and include in the box!  (Sorry, this pendant isn't part of today's project, only the box is; however, if you want a tutorial, please let me know.  I'm sure most of you already know though how to put one of these together using Tim Holtz' idea-ology Facets):

Would you like a close up?  Yes?  Okay, here you go:

Oops, there's my reflection in that rhinestone!!!  LOL!!!  Okay, before I start the tutorial, I wanted to show you where my inspiration for this box came from.  I recieved an item in this adorable box -- one picture shows the box closed and the other with the two (2) lids open revealing the inside of the box:

To begin the tutorial, I first cut out the patterns from the cut.file:

These pattern pieces are the box cover, the box, and (optional) panels.  Beginning with the box cover, you will see I have added small tick marks (cuts) on the sides -- which I've highlighted in ink; these marks indicate where the cover will be folded across from one side to the other :

I bone-folded these tick marks from one side to the other separating the cover sections as shown below, then put the cover aside:

Grabbing the box pattern, I bone-folded the 4 tabs and 4 sides of the box:

After all the folds were made, I applied glue to the 4 small corner tabs of the box pattern as shown below, and attached the tabs to the inside side folds ( do both sides):

Here's the assembled box:

Now I go back and get my box cover.  I apply glue to the 3 inside panels only, leaving the 2 outside panels without glue (these are the 2 lids that open onto the box):

Taking the box, I centered and aligned it onto the box cover and attached them together (careful centering is necessary for folding up and attaching the sides of the box cover to the sides of the box to align properly):

This box itself is now complete!!!  See how it opens?!!!  But I'm not finished, I want to add my panels!  After closing the box, I took the top cover panel, aligned it, and glued it in place.  (NOTE:  After aligning the panel there will be access paper which will have to be cut off the bottom edges of the box; I turned the box over after gluing on the panel and cut off the access).  My box now looks like this:

Because my box is made of matching decorative paper, I don't need the smaller side panels included on the cut.file for the box sides, so all I need to do is add the longer side panels to the front and back sides of my box cover:

 

Last but not least -- embellishing my box!!!   I added Stickles along the edges of the side panels, both sides of the outer sides of the box, and along the edge of the top box cover and panel -- I love the bling!  Next I attached a small ribbon bow, and accented the bow and across the top of the box with a Pearl Pen, and then just tossed on a couple of flowers I had lying around.  And how about this set?!!!  Kinda cute, huh?

The cut.file, and a .gypsy file, is available at the end of this post.  Of course, it's a box, so it was easiest for me to do the file using the George cart; however, if you do not have George, please leave me a comment and I'll get back to you to determine further directions.

Thanks for stopping by, and...

I'll be seeing you!

each side opens box.cut

each side opens box.gypsy